Exhaust flanges ... last call ...

weaselnoze · December 23, 2004, 11:55:50 PM

Quote from: CAN_Porn*Starso the install is pretty painless?
just chop the stock pipe install the muffler using your flange?
do i need to weld it or anything? or can i install it without a welder?

im willing to bet you have been asked this question so manny times.

hahaha....painless :lol:

The Buddha · December 24, 2004, 08:17:46 AM

Quote from: jusAgshow much is shipping? no paypal?

Shipping is ~$8 or so, and add $2 for paypal bite ...
Send $50 to seshadri_srinath@hotmail.com
Cool.
Srinath.

The Buddha · January 04, 2005, 09:21:42 PM

OK 1 last stainless mid pipe one left ...
And most likely 5-6 more I have round things for, and can make with steel mid pipe ...
Cool.
Srinath.

weaselnoze · January 04, 2005, 10:02:57 PM

i'd buy it if i had something to put it on. wait! maybe i could make a musical instrument out of it. cept for thats pretty ghey

The Buddha · January 04, 2005, 11:58:15 PM

Not the new flanges ... they have 6 more laser drilled holes ... all around the edge ... lets see if you call them ghey ... :lol: :lol: :lol:
Cool.
Srinath.

fettcols · January 05, 2005, 04:48:00 AM

If there's an '04 model available count me in....

fett

weaselnoze · January 05, 2005, 05:26:16 AM

6 more holes? is it just for detail?

The Buddha · January 05, 2005, 10:04:01 AM

That 04 was what held me up for so loooong ... and hence yea 04 ... Turns out ... the pipe is the same as old size for ~ 2 inches from the last weld on the header before it flares out to 2.1 inches ... so 04 pipe is same as 89-00 pipe ... just cut it right where it has the 2 inch pipe slipped on ...
And weaselnoz 6 more laser drilled holes ... Not just for looks ... they where there when I got it ... see I am picking up stuff off the scrap pile at different scrap places ... what they throw is what I got ... these have holes ... OK dont bother me ... and doesn't affect our functionality ...
Cool.
Srinath.

The Buddha · January 05, 2005, 10:37:44 AM

Fettcols - If its just 1 its going to be a bit of a pain ... cos all material is cheaper and shop rates are cheaper by the dozen or 1/2 dozen ... so I'll wait a bit to see if more people order up ...
So basically I am checking if more people jump in ... I can make 6 I think, have 6 flanges ... and will be more efficient to do that ...
Cool.
Srinath.

2xs · January 05, 2005, 02:19:21 PM

Are you doing these new 2004 pipe/flange setups all regular steel or part stainless? The reason I ask, I might order an all regular steel one too...if they don't have the bend crimps that result when stainless is bent.

chinox22x · January 05, 2005, 02:30:07 PM

Quote from: 2xsAre you doing these new 2004 pipe/flange setups all regular steel or part stainless? The reason I ask, I might order an all regular steel one too...if they don't have the bend crimps that result when stainless is bent.

yeah...might get one too if i don't like the "bend" on the stainless one

The Buddha · January 05, 2005, 10:15:22 PM

2xs - The mid is stainless ... OK I better clear up somehitng ... I am not exactly volunteering to make steel mid pipe flanges ... just that ... if there is numbers its possible ... I have 1/2 a mind to send off the round things to whoever wants to blow a hole in it and make a mid pipe ... OK if I get 5-6 orders I'll crank out the steel ones, remember you need wiley co's to work with these and they are disappearing fast off ebay ... down to about 20 the last I saw ... so instead of saying you want steel or this or that ... just get a wiley co first ... you can always argue with me later ... Steel, stainless crap ... somehting will be welded into a flange ...
OK that wrinkle in the bend ... Stainless doesn't crush much at all ... steel will shrink more ... whihc makes it stay un wrinkled ... trade off I guess ... I doubt it is ever going to get noticed ... cos its under the bike, 2 of the wrinkles (There is 3) are pointing to the wheel and if you paint over ... its going to be hard to see ...
Cool.
Srinath.

jusAgs · January 05, 2005, 11:26:50 PM

sooo :guns:

does it matter which cans we get? for any particular bike?

The Buddha · January 05, 2005, 11:36:31 PM

I think they are all the same ... but CBR 900 (95-98 ) and GSXR 750 (96-99) and YZF 1000 (97-99) should be fine. The flange has drilled holes to match your can's threaded holes ... as long as we know what your hole configuration is ... should be no problem ...
Cool.
Srinath.

The Buddha · January 06, 2005, 10:49:14 PM

OK all the flanges are done and ready to go, tommorow most likely I will pack it ... saturday its getting sent ... dont ask busy day tommorow ... job hunting is a full time job ...
Now for some bad news ... I am looking at another large length of SS pipe ... this time a 304 stainless ... AKA shiny stainless .... I might make the next round of flanges with those ... not steel ... So every one that wants steel ... I'm afraid you're getting stainless as well ...
Odd bunch of people ... stainless is the most expensive material there is ... its the champage of metals ... OK OK no one is talking gold or silver ... we cant make exhaust pipe from that ... and people want steel ... Anyway I like SS cos I have have the un used part lying about in my back yard and its never gonna rust ...
Cool.
Srinath.

chinox22x · January 07, 2005, 07:19:10 AM

Quote from: seshadri_srinathOK all the flanges are done and ready to go, tommorow most likely I will pack it ... saturday its getting sent ... dont ask busy day tommorow ... job hunting is a full time job ...
Now for some bad news ... I am looking at another large length of SS pipe ... this time a 304 stainless ... AKA shiny stainless .... I might make the next round of flanges with those ... not steel ... So every one that wants steel ... I'm afraid you're getting stainless as well ...
Odd bunch of people ... stainless is the most expensive material there is ... its the champage of metals ... OK OK no one is talking gold or silver ... we cant make exhaust pipe from that ... and people want steel ... Anyway I like SS cos I have have the un used part lying about in my back yard and its never gonna rust ...
Cool.
Srinath.

sweet..i can't wait!

jusAgs · January 07, 2005, 08:02:45 PM

hey save one for me

checks in the mail

The Buddha · January 08, 2005, 10:23:47 PM

Yea its yours ... I guess I am making 6 more ... and its all shiny stainless mid pipes ... no steel for me ... Yea flanges are steel ... mids are SS ... OK this is larger dia SS pipe than the stock size ... so I am going to cut a slit and send a clamp along with it this time ... so stuff some exhaust tape in the middle and clamp it ...
Cool.
Srinath.

News:

Exhaust flanges ... last call ...