News:

New Wiki available at http://wiki.gstwins.com -Check it out or contribute today!

Main Menu

Flanges and wiley co - available again

Started by The Buddha, March 01, 2006, 03:40:09 PM

Previous topic - Next topic
Print
Go Down Pages 1 ... 12 13 14 15 16 17
User actions

joedude

#260
June 26, 2006, 10:02:48 PM
Quote from: seshadri_srinath on June 26, 2006, 07:05:47 PM
OK welder got in, and got 20 made, we only had 20 pipe pieces, have 7 more rounds though ... so 7 more will be made ...
If I forget please make a note of these things ...
The header pipe should be cut plenty longish ... 4+ inches ...
On a 01+ ... I ll spread the slider part ... but if it doesn't fit ... a muffler shop will be able to spread it just fine ...
If you think its a bit loose, put a muffler clamp on it. My header pipe has too much wear, I dunno if its tight or loose anymore ...
More to come ... I'll send it in a day or 2 ...
Cool.
Srinath.

Wohoo Srinath!
FTHRWYFL - Forget the Hype, Ride What You F@$#%&n Like!

1996 GS500, Red, w/ Fenderectomy, Complete LED Dash, K&N lunchbox, Rejet
Mods to be installed: Wileyco Slip-on, and Headlight Fairing

b-spec

#261
June 27, 2006, 12:09:51 AM
just sent 57 usd. i hope its enough to get to canada.  :thumb:
'94 GS twin devil's blood red rat bike purchased 18/02/06 with 60k+kms. 145 mains, K&N filter. Yoshimura RS-3_srinath flange. top speed: 180km/h decending last 400m of cypress mt. road.

Wrecent_Wryder

#262
June 27, 2006, 01:26:05 AM Last Edit: August 18, 2007, 06:36:25 AM by Wrecent_Wryder
h6
"On hiatus" in reaction to out-of-control moderators, thread censorship and member bans, 7/31/07.
Your cure is worse than the disease.
Remember, no one HAS to contribute here.

The Buddha

#263
June 27, 2006, 08:01:11 AM
OK I had an idea ...
I'll make a insert ... if its 89-00 use the insert, if not dont ... if you hack it too short well maybe get it welded or clamped tight etc ...
The info here isn't for all production runs ... man no 2 of these damn things are identical ... Heck one guy got one which was so far frocked up ... he had a hole big enough to stick his little finger through between flange and can ... nuts ...
But anyway we will figure somehting for you ... You're so special ...  :laugh:  :laugh:  :laugh:
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

nmred

#264
June 27, 2006, 09:14:49 AM
Srinath, just sent out the payment thru paypal. Let me know if you got it. Thanks again.
Depression is anger without the enthusiasm

ImJustPondering

#265
June 27, 2006, 09:33:35 AM
awesome, now my bike can sound like a real one soon!  :o

The Buddha

#266
June 27, 2006, 09:37:15 AM
I'll check in a bit ...
BTW I may have more than the 27 I am making ... OK maybe not ... but certainly seems like it.
I'll post instructions on this page in a bit. I think that insert idea will be the best. Watch for pics.
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

The Buddha

#267
June 27, 2006, 11:55:35 AM
OK please tell me ... no one bought a 4 bolt can ...
That link I posted now has a couple of 4 bolters ... That wont fit my flange ... OK you'll have to drill then it will fit ... not too hard ... but straight on ... no.
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

nmred

#268
June 27, 2006, 12:09:23 PM
No my can has 3 holes. THAT SOUNDS SO BAD!!!!!

Joe
Depression is anger without the enthusiasm

average

#269
June 27, 2006, 12:11:44 PM
Quote from: nmred on June 27, 2006, 12:09:23 PM
No my can has 3 holes. THAT SOUNDS SO BAD!!!!!

Joe
3 mounting holes, big guy   O0
R.I.P
Rich(Phadreus)
90 gs5 04 Fairings(that's right)
LP flushmounts up front  shortened turn signals
Kanatuna rear wheel swap
Kat FE

The Buddha

#270
June 27, 2006, 04:52:52 PM
OK who's got an 01+ ... probably a non issue but better I know ...
Yea I may fix them all to work on all years ... but that means more time ...
So best to send 01 type stuff to 01 guys ...
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

Wrecent_Wryder

#271
June 27, 2006, 05:39:51 PM Last Edit: August 18, 2007, 06:33:08 AM by Wrecent_Wryder
[7
"On hiatus" in reaction to out-of-control moderators, thread censorship and member bans, 7/31/07.
Your cure is worse than the disease.
Remember, no one HAS to contribute here.

The Buddha

#272
June 27, 2006, 06:07:02 PM
Aaah ... you got an 89-00 header you're fitting on an 01+ and those are already cut ... not a problem ... I got the pipe for ya ... you'd be fine ...  O0 ... trust me  :laugh: ... If you are fitting it on the 02 with its headers you'd be trouble ... BTW if anyone wants to get the flange located and tacked or welded, no matter what it will work ...
Just slip fitting on an 01+ is a wee bit more tricky ... cos the blooming 01 head pipe is 2 different diameters where they connect up. I am spreading it to slide over the larger pipe, and you leave a good bit of that pipe (3 inches or so) intact, and then slide them on ... then you can trim your header for a better, tighter fit.
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

samhkang

#273
June 27, 2006, 11:10:18 PM
Way to go srinath, glad to hear that they are ready now. I just can't wait to cut the damn stock muffler off!! btw, what is the best method to cut? I want a clean/painless cut for my precious baby G.  :icon_razz:
'05 GS500F Blue/White
Fenderectomy, K&N filter
Lockhard short stalk V turn signals
Fiamm C 40310 High Note Horn
Gorilla cycle alarm
Wileyco slip-on
2" Lowered bike at http://samhkang.tripod.com/my_2005_gs500f/

average

#274
June 27, 2006, 11:10:58 PM
Grinder,baby! 14.99 at harbor frieght.   O0
R.I.P
Rich(Phadreus)
90 gs5 04 Fairings(that's right)
LP flushmounts up front  shortened turn signals
Kanatuna rear wheel swap
Kat FE

Wrecent_Wryder

#275
June 28, 2006, 03:54:06 AM Last Edit: August 18, 2007, 06:32:39 AM by Wrecent_Wryder
[j
"On hiatus" in reaction to out-of-control moderators, thread censorship and member bans, 7/31/07.
Your cure is worse than the disease.
Remember, no one HAS to contribute here.

The Buddha

#276
June 28, 2006, 11:48:03 AM Last Edit: June 29, 2006, 07:20:05 AM by seshadri_srinath
The paypal list.

uclajoebruin - 04
imjustpondering@yahoo.com X 2 - 04
David Tyler 
Brian Holahan   
Snap
Wrecent - new bike, old pipe I guess right.
teh_asdf - X 2 - 04
Luc Mallet    Grrrr canada ... 96
'b-spec' - Again Grrrr canada ...
Joseph Greig - 93

The ones who sent checks I will add in from home tonight.
In any case I believe I have a few more rattling around ... Prolly coser to 7-8 ... grr ... but hey I ask for 20 and get 27 round things ...  :thumb: ...
Pics comming but most likely I will send 01+ specials and 89-00 specials ... for now, we start crossing over and that when it gets sticky ...
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

The Buddha

#277
June 28, 2006, 11:49:57 AM
Quote from: samhkang on June 27, 2006, 11:10:18 PM
Way to go srinath, glad to hear that they are ready now. I just can't wait to cut the damn stock muffler off!! btw, what is the best method to cut? I want a clean/painless cut for my precious baby G.  :icon_razz:

What ... you too lazy to bite the pipe off like the rest of us ...  :laugh:
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

teh_asdf

#278
June 28, 2006, 02:06:38 PM
As far as my 2 go, both will be for 04's (just to let you know).

Dwn4whadever

#279
June 28, 2006, 02:11:02 PM
Are the bars in the making too?  :thumb: :thumb: :thumb:
A common mistake that people make when trying to design something completely foolproof, is to underestimate the ingenuity of complete fools....

Thanks to advances in automation, Nike shoes will be made by robots. Unfortunately, the robots will be made by children in Malaysia.
Print
Go Up Pages 1 ... 12 13 14 15 16 17
User actions
SMF spam blocked by CleanTalk