Text only | Text with Images

GStwin.com GS500 Message Forum

Main Area => General GS500 Discussion => Topic started by: dlooney1 on April 07, 2005, 05:45:31 PM

Title: shitty swing arm on the 04 gs 500f
Post by: dlooney1 on April 07, 2005, 05:45:31 PM
i change the sprokets this past sat. so i was poping a couple wheelies here and there and on the swing arm if u looking from the back it has 2 little metal plates on the end of the swing arm they almost bent right in the arm how can i make it stronger???
Title: shitty swing arm on the 04 gs 500f
Post by: john on April 07, 2005, 05:49:50 PM
Buy a GSX-R1000  :lol:
Title: shitty swing arm on the 04 gs 500f
Post by: Mat on April 07, 2005, 07:35:10 PM
buy 4 plates and put 2 on each
Title: Re: shitty swing arm on the 04 gs 500f
Post by: The Buddha on April 07, 2005, 07:36:09 PM
Quote from: dlooney1i change the sprokets this past sat. so i was poping a couple wheelies here and there and on the swing arm if u looking from the back it has 2 little metal plates on the end of the swing arm they almost bent right in the arm how can i make it stronger???

Oh yea ... pay srinath like $30-40 and have some made from 1/4 inch steel flat bar ...
What ... who said that ...  :o
Cool.
Srinath.
Title: shitty swing arm on the 04 gs 500f
Post by: cummuterguy on April 07, 2005, 07:59:35 PM
also, check the torque on your axle nut... if it's too loose, those little plates are the only things keeping your wheel from shooting forward.
Title: shitty swing arm on the 04 gs 500f
Post by: Blueknyt on April 07, 2005, 09:08:34 PM
yeah, i know your pain dude, i hammered mine flat and found some Angle iron and welded it to the plate sl its like a triangle and then drilled a whole from the backside through the corner of the angle iron. now with the grippyest tire on that bandit wheel it doesnt move.
Title: shitty swing arm on the 04 gs 500f
Post by: EDub on April 07, 2005, 09:18:01 PM
i did this as well, but it was because my chain was too tight along with the torque from the wheelies.  I would check chain slack if i were you.
Title: shitty swing arm on the 04 gs 500f
Post by: stefman722 on April 07, 2005, 11:10:45 PM
Hey,


I just changed my F to a 14t front sprocket tonight and went out with my buddy. A 14t in the front is crazy. I bought a 15t aswell, but started with the 14t. Revs like crazy, and best off all, i can do wheelies without, thats right, WITOUT using the cluth  :thumb: And my plates were bent as well after tonight, so i just put them in a press and straighten them out. Worked alright. I am going to the zuki dealer tomorrow, ill get him to make me some thick suckers.
Title: shitty swing arm on the 04 gs 500f
Post by: Organdoner on April 08, 2005, 05:39:45 AM
Can you over torque your axle nut?
Title: shitty swing arm on the 04 gs 500f
Post by: davipu on April 08, 2005, 09:46:03 AM
yep, it is really easy, you will notice that the rear tire is really hard to spin
Title: shitty swing arm on the 04 gs 500f
Post by: Mountaineer on April 08, 2005, 09:54:40 AM
If the axle nut is tight, how the $%^&* do you get pressure on the adjuster plates???????
Title: shitty swing arm on the 04 gs 500f
Post by: davipu on April 08, 2005, 10:05:39 AM
well if any of you had a repair manual, you whould know that you snug the nut down, adjust chain adjusters, and then torque nut down.  the reason the crap bent in the first place is because it wasn't adjusted properly and the nut wasn't torqued correctly, and then you applied a large amount of touque to the center of the adjusting plate by wheeleing.  hell, you may have just started beatig on it with a hammer and saved yourself alot of time and effort.
Text only | Text with Images