my gages are ugly and old i search everywere for buy new ones or mint condition used. with no luck
there any aftermarket a different bike or something that can be fit on the GS !! any universal gauges diferent bike model !! I dont know some1 can help !
I do not know of any direct replacement gauges.
But other gauges can be adapted, depending on your ability.....
I have 1st Gen (99-02) SV650 gauges on my 97. I modified a SV speed sensor to fit the GS axle. Just had to make a bushing to fit in the inside.
My 92 has '02 SV650S gauges. Still working on the speedo sensor for the GSXR front end, which requires 4 magnets attached to the rotor.
The tachs and lights were easy to wire, just need to be able to read a wire diagram.
What's ugly about yours? You could probably spruce them up and make them better than new.
http://gstwins.com/gsboard/index.php?topic=36893.0
:thumb:
Quote from: Nikolas on July 20, 2007, 06:41:22 PM
What's ugly about yours? You could probably spruce them up and make them better than new.
the plastic housing is crack and have some holes . the tacho has burn in the back by the bulb and the inside of the tach panel is burned and you can see thru the black the light. i will post some photos tomarrow !!
the acewell is gawd awful ugly...i like the standard gauges but a sv set would look pretty good too
Quote from: frankieG on July 20, 2007, 08:39:29 PM
the acewell is gawd awful ugly...i like the standard gauges but a sv set would look pretty good too
I wouldn't say its very ugly at all. Much better looking than the stock gauges.
Here are a few pics, Im planning on getting one as soon as I get the money. They run about $150, not bad at all. The US distributor for them is 60 miles from me.
(http://thumbnail.image.rakuten.co.jp/@0_mall/hatoya/cabinet/ngk/ace3803-01.jpg)
(http://www.bikerscrown.cz/foto/obr/obr2273-9804.jpg)
This one shown with the surround you get with certain models to replicate all the stock LED function.
(http://www.bikerscrown.cz/foto/prodm/produkt2273.jpg)
Quote from: slowinthestraights on July 20, 2007, 09:11:21 PM
Quote from: frankieG on July 20, 2007, 08:39:29 PM
the acewell is gawd awful ugly...i like the standard gauges but a sv set would look pretty good too
I wouldn't say its very ugly at all. Much better looking than the stock gauges.
Here are a few pics, Im planning on getting one as soon as I get the money. They run about $150, not bad at all. The US distributor for them is 60 miles from me.
(http://thumbnail.image.rakuten.co.jp/@0_mall/hatoya/cabinet/ngk/ace3803-01.jpg)
(http://www.bikerscrown.cz/foto/obr/obr2273-9804.jpg)
This one shown with the surround you get with certain models to replicate all the stock LED function.
(http://www.bikerscrown.cz/foto/prodm/produkt2273.jpg)
I wanted to use one of these on the bike I'm building.Any one use this before?
that acewell use mecanichal cables or electrical cables for the tacho and speedo . in the photo looks like it was mechanical cabl like GS gauges!
can't like them at all, they look like cheap pda's you find at mardens
Its Electrical , my one , the model 3100 , a single wire that goes round the coil , for the RPM , then a wire that goes down , with a small magnet attched to the Front wheel , its easy and looks good , my tastes tho
If you just want to freshen up your stock ones...
http://cgi.ebay.com/ebaymotors/Suzuki-GS500F-Meter-Cover_W0QQitemZ290140156628QQihZ019QQcategoryZ35583QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
-Anti 8)