Okay.  Wileyco. can from e-bay? Check.
Flange from Srinath? Check.

What jets to use for this set up:

#40 pilots.
125 main.
#4 washer.

Correct?

40/125/1 #4, 3 truns float stock ... if you have paper filter in airbox...
Cool.
Srinath.

OK Great ... now there is over 30 and more than that there was a couple that weren't scratched or dented as per their description ...
On a side note ... I got 3 payments and 6+ that I can make with the material I have ... My goal is to be done with the flanges soon ... looks like it might not happen ... but anyone that's needing a flange please send me $$ cos when the 3 more are sold ... no telling when I'll make more ... cos round things aren't there ... I'll have to find them ...
Cool.
Srinath.

when will you ship out those flanges?

I am on it ... maybe early to mid next week.
Cool.
Srinath,

There was no defect in the can I got.  There was what could be considered a scratch, about a 1/4 inch long, on the side that faces the wheel.   So, big deal.  For $50?  I'd say I stole it.

got my pipe friday, not a single scratch, srinath could you send me pm with your address so i can send you a check? thx

Quote from: seshadri_srinathI am on it ... maybe early to mid next week.
Cool.
Srinath,

dont forget about mine....

Anyone who has one on their GS already, What does it sound like?! let me know. thanks

Quote from: jusAgs

Quote from: seshadri_srinathI am on it ... maybe early to mid next week.
Cool.
Srinath,

dont forget about mine....

I wont forget ... however I have serious trouble with names and handles and everyhting ... so if you send me paypal ... I'll send it to the address in the paypal, if check ... I'll send to address on check or the note that is attached to it.
Cool.
Srinath.

Quote from: stefman722Anyone who has one on their GS already, What does it sound like?! let me know. thanks

It sounds like Vrooooooooooooooooooom.  And when it's at idle it's like whoomp whoomp whoomp whoomp whoomp whoomp.whoomp whoomp.  

When it's idling in the garage and I stand in my kitchen it sounds like a Huey helicopter is hovering nearby.

I'll work on getting a nice quality sound byte of it posted here.

Sound bite would be cool. . .

Hey, it is a motorcycle.  Is should turn some heads?  Right?  

My neighbors probably already hate me.   Screw 'em.  It is going to look  boss!!!

Quote from: Dom

Quote from: stefman722Anyone who has one on their GS already, What does it sound like?! let me know. thanks

It sounds like Vrooooooooooooooooooom.  And when it's at idle it's like whoomp whoomp whoomp whoomp whoomp whoomp.whoomp whoomp.  

When it's idling in the garage and I stand in my kitchen it sounds like a Huey helicopter is hovering nearby.

I'll work on getting a nice quality sound byte of it posted here.

Do it for tonight!!!  

just installed mine on my '04.  

sounds good.   midpipe was a little bit of a hassle to install.  it was actually hitting the brake lever and i had to finaggle it a little bit.  

this sounds much better than stock.

Its not hitting now right ... The slip fit actually doesn't let it turn unless you have the can on and the bolts loose and you have a long rod inbetween the bolts and use that leverage ... but tight fit is needed else it will leak there ... anyway its not hitting now right ...
Cool.
Srinath.

Minds eye:

Ah, I get it. . . put the can on, very loose, slip fit the mid-pipe.  Bolt can to flange, very loose. . .

Slide long rod/lever between can and flange and use bolts to rotate mid-pipe like a clock, sealing the fit of the mid pipe.  

Correct?

Fit the can to mid pipe and position it and finnagle it ... now once you're sure the position is right ... Remove the can, knock the flange in with a mallet ... and bolt can back in ... OR wait a sec ... the ones I am making now are going to fit loose ... you position it etc and get it all lined up and make a chalk mark, then remove it and slip on the small piece of pipe I have in it ... and now it will fit tight ... Yes I made a small mod to the design ... the pipe fits loose on the header, but there is a small pipe that fits on the header and takes up the slack ... you'll know when you get it.
Also people many times forget to sand the short piece they are slipping on ... its gotta have some wd 40 and be smoothly sanded ... then the mid pipe will slip on and rotate with a little effort. Anyway ... the new ones should go on easier ... they are larger ID ... just wait and see ...
Cool.
Srinath.

Got my can, can't wait to get my flange  

It's in perfect condition except for two or three microscopic scrape/scratches wheelside. Such a great value. Can't wait to hear how it sounds.

http://home.earthlink.net/~keith_erwin/images/wileycocan.jpg

Yea Told y'all so ... those guys over describe ... and like they write up dirt spots as scratches and defects ... heck off the shelf at bike stores I have seen worse ... on exhausts that cost like $900+ ... They just describe themselves right out of the sale ...
Cool.
Srinath.

Live, late breaking, flange update?