News:

Need a manual?  Buy a Haynes manual Here

Main Menu

The Buddha doing carbs again

Started by The Buddha, March 19, 2008, 11:41:44 AM

Previous topic - Next topic
Print
Go Down Pages1
User actions

The Buddha

March 19, 2008, 11:41:44 AM Last Edit: April 04, 2008, 06:10:44 AM by The Buddha
K I had silently stopped it ... but its getting to the point where I may be able to do em again.
$45 for a re-jet, light cleaning is included as in, I open the floats, pilots, mains, diaphragms, etc ... Add return shipping.
Total sheite carbs may cost more.
Sheite being stripped and stuck may cost more.
I'll drill out the caps on the mix screws - included in the $$ but nothing else needing drilling is. Starts at $5 per. I break it, you buy it ... Or, like your risk. However in over a 100 carbs (lost count at 100 I'd say, heck I did 3 of seamax's carbs over the last 3 years - dude it have been cheaper for you to learn) I am yet to lose a carb. I've drilled out a good few pilots, and several 100 float screws and top screws.
So, Yea, send it over, PM me for address. Make sure you add a note in the carb box as to what setup you got, I am working on turn around times, which have been dismal this winter, but its gonna get better, a lot better I hope.
BTW I just did seamax's carbs and had it back to him in under 3 weeks ... and he needed an impossible part (a set of needles). I also send one more of my neighbors a set of slides, guides and diaphragms in 2 days flat ... literally 2 days from when I bought the carb rack at the wreckers.
Cool.
Buddha.

-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

seamax

#1
March 19, 2008, 01:40:39 PM
He does excellent work.  :thumb:

If I wasn't so lazy I WOULD learn but I'm trying to stimulate the economy.  :icon_mrgreen:

The Buddha

#2
March 19, 2008, 03:09:28 PM Last Edit: April 04, 2008, 06:11:06 AM by The Buddha
This set was good seamax. I think the first set you sent me ... still stands as the dirtiest carb I have seen. I also had to drill out literally everything in that first one. If that worked (I also was 3-4 years less experienced then) ... all the rest after it is a piece of cake.
Cool.
Buddha.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

average

#3
March 19, 2008, 09:52:32 PM
Great! My carbs are no longer the worst the Sri has ever seen! YEAAAAAAAAAAAA!
:laugh: :laugh: :laugh: :laugh: :laugh: :laugh: :laugh: :laugh: :laugh: :laugh: :laugh: :laugh: :laugh:
Diaz
O0
R.I.P
Rich(Phadreus)
90 gs5 04 Fairings(that's right)
LP flushmounts up front  shortened turn signals
Kanatuna rear wheel swap
Kat FE

The Buddha

#4
March 20, 2008, 04:53:31 AM
Your carbs weren't the worst ... But your tank was pretty darn close to it  :thumb:.
Cool.
Srinath.
-----------------------------------------------------------------
I run a business based on other people's junk.
-----------------------------------------------------------------

seamax

#5
March 20, 2008, 07:59:46 AM
Quote from: seshadri_srinath on March 20, 2008, 04:53:31 AM
Your carbs weren't the worst ... But your tank was pretty darn close to it  :thumb:.
Cool.
Srinath.

You do tanks too?!  Hmmm.
Print
Go Up Pages1
User actions
SMF spam blocked by CleanTalk